Share on Facebook
Tweet
Send email
S&P SISTEMAS DE VENTILACIÓN, S.L.U.
Llevant, 4
Polígono Industrial Llevant
08150 Parets del Vallès
Barcelona – Spain
consultas[zav]solerpalau[teč]com
www.solerpalau.com/en-en/home
Product description
Housing
The housings for the TD-160 to TD-2000 N fans are made of plastic; the TD-4000 and TD-6000 models are made of galvanised sheet steel with an epoxy coating. The housing consists of a mounting rail with two connections and a motor, which is connected to the connections via quick-release clips. The design allows the motor section to be removed without the need to disconnect the ducting.
Impeller
The impellers of the TD-160 to TD-2000 N fans are made of plastic, whilst those of the TD-4000 and TD-6000 models are made of aluminium.
Motor
The AC motors in the TD-160 to TD-350 fans have dual windings, which allow for operation at two different speeds. The TD-500 to TD-2000 N fans have three windings. The TD-4000 and TD-6000 have a single winding and can be regulated by varying the voltage. The motors are fitted with a thermal fuse (TD 160–TD 350) or thermal protection (TD 500–TD 6000). The bearings are ball bearings with grease-filled for the entire service life. Insulation class B, protection rating IP44 (TD 160–2000 N), insulation class F, protection rating IP54 (TD 4000 and 6000). TD and TD-T fan motors are single-phase for 230 V, the TD 4000 TRIF are three-phase for 230/400 V, and the TD 6000 TRIF are three-phase for 400 V.
Terminal block
is located on the fan casing; in single-phase models, it contains a starting capacitor.
Speed control
For double-wound AC motors (TD 160–350), the speed is switched between two stages using REGUL 2 or COM 2 controllers, or by adjusting the voltage using REB (continuous control) or REV (five-stage control). For motors with triple windings (TD 500 – TD 2000 N), the speed is switched in three stages using COM 3 or INTER 4P controllers, or speed control can be achieved by adjusting the voltage using REB controllers (continuous control) or REV controllers (five-stage control). The TD 4000 and 6000 can only be controlled by varying the voltage. The TD 4000 and 6000 TRIF can be controlled by varying the voltage or using frequency converters. The TD-T 160-350 cannot be controlled; the TD-T 500-800 3V can only be controlled using the INTER 4P speed selector switch.
Installation
The fans can be installed in any position. The casing must not transmit mechanical stress from the ductwork. It is recommended to use a flexible connection to the ductwork.
Variants
• TD basic version
• TD-T version with adjustable run-on time of 1 to 30 minutes, single-speed (for DN 100–125 ducting)
• TD-T 3V version with adjustable run-on time of 1 to 30 minutes, three-speed (for DN 150–200 ductwork)
Parameters
| Základní údaje | |
|---|---|
| Engine type | AC |
| Fan type | diagonal |
| Mounting | Pipeline |
| Max. air temperature | 60 °C |
| Připojení | |
| Diameter of inlet connection pipe | 315 mm |
| Diameter of the connection pipe at the discharge | 315 mm |
| Elektrické parametry | |
| Power supply | 230 V |
| Ingress Protection | IP44 |
| Maximum power | 273 W |
| Maximum current | 1,10 A |
| Další | |
| Weight | 8,40 kg |
| Maximum speed | 2 640 min⁻¹ |
Adherence to these instructions should not pose any safety, health or environmental risks in accordance with EC directives (CE marked). The same applies to other products used in the device or during installation. Consider the following warnings:
• Observe the safety instructions to prevent damage to the device or personal injury.
• The technical information in this manual must not be changed.
• It is forbidden to interfere with the motor of the device.
• In order for the device to comply with EC directives, the device must be connected to the mains in accordance with the applicable regulations.
• The device must be installed in such a way that under normal operating conditions it cannot come into contact with any moving part and / or live part.
• The device complies with the applicable regulations for the operation of electrical equipment.
• Always disconnect the device from the power supply before carrying out any work on it.
• Appropriate tools must be used when handling or maintaining the device.
• The device must only be used for the purposes for which it is intended.
• This appliance is not intended for use by children under 8 years of age and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible person. The user must ensure that children do not play with the device. Cleaning and maintenance of the appliance must not be carried out by children without supervision.
