EC-9N electric heater

Electrically heated axial fans suitable for drying wet areas and for heating in industry and construction.
Read more
B2B clients will see their prices after logging in
20 316,00 CZK excl. VAT
24 582,36 CZK incl. VAT
Availability: on request [22.8.2025, 16:26] Update

Insert into the design HVAC program

Product code: SP181100140
EAN: 8413893138873
Manufacturer: S&P SISTEMAS DE VENTILACIÓN, S.L.U.   Read moreRead less

S&P SISTEMAS DE VENTILACIÓN, S.L.U.
Llevant, 4
Polígono Industrial Llevant
08150 Parets del Vallès
Barcelona – Spain
consultas[zav]solerpalau[teč]com
www.solerpalau.com/en-en/home

Product description
Cabinet

It is made of sheet steel, coated with a burning varnish. A swivel bracket made of sheet steel is attached to the cabinet, which allows the position of the fan to be adjusted.

Running wheel

is axial, moulded from Al sheet. The blades are performance optimised.

Motor

asynchronous with short armature and shielded pole, for continuous operation. Motor has plain bearings with grease packing for life. Motor has overload protection. IP24 protection.

Regulation

is carried out externally by a CR 25 switch or by a CR 25 switch and a TR thermostat. Three different operating modes can be selected via the switch (fan only, fan and half heating power, fan and full heating power). If a thermostat is also used, the unit starts automatically in the mode selected on the CR switch. In addition, it is possible to set whether the thermostat starts the whole unit (fan and heater) or only the heater (when the fan is running continuously).

Electrical connection

Connection via cable routed from the cabinet through a grommet, the unit is designed for fixed mounting.

Mounting

The unit is mounted on the wall using the hanger included in the delivery. The minimum distances from the walls are shown in the illustration. Care must be taken to ensure that the inlet and discharge sides are not covered by the heating rod enclosure. In this case, the air flow through the cabinet could be restricted, thus increasing its temperature and causing a fire hazard. If the air temperature rises, the unit will be switched off by the safety thermostat, whose reset button is located on the top of the cabinet. The switch and thermostat are wall mounted.

Noise

emitted by the fan is measured at a distance of 1.5 m in the free acoustic field is given in the table.

Variants

- EC-3N basic version 3 kW/230 V
- EC-5N basic version 5 kW/400 V
- EC-9N basic version 9 kW/400 V
- EC-12N basic version 12 kW/400 V
- EC-15N basic version 15 kW/400 V

Instructions

Electrically heated fans are suitable for drying wet areas and for heating in industry and construction. The places of use are mainly production halls, warehouse halls, common rooms, churches, exhibition halls, buildings and construction site facilities, garages and workshops.

Highlights

A safe distance from combustible structures as specified in the user's operating rules must be maintained.

Full description
Safety regulations

Adherence to these instructions should not pose any safety, health or environmental risks in accordance with EC directives (CE marked). The same applies to other products used in the device or during installation. Consider the following warnings:

• Observe the safety instructions to prevent damage to the device or personal injury.
• The technical information in this manual must not be changed.
• It is forbidden to interfere with the motor of the device.
• In order for the device to comply with EC directives, the device must be connected to the mains in accordance with the applicable regulations.
• The device must be installed in such a way that under normal operating conditions it cannot come into contact with any moving part and / or live part.
• The device complies with the applicable regulations for the operation of electrical equipment.
• Always disconnect the device from the power supply before carrying out any work on it.
• Appropriate tools must be used when handling or maintaining the device.
• The device must only be used for the purposes for which it is intended.
• This appliance is not intended for use by children under 8 years of age and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible person. The user must ensure that children do not play with the device. Cleaning and maintenance of the appliance must not be carried out by children without supervision.

Downloads
Technical sheets, manuals and declarations
Datasheet .pdf (158.49 kB)
Operating Instructions .pdf (504.78 kB)
CAD files
2D .dwg (361.47 kB)
Contact Us