TMPT/6-24-0,18 IP55 anti-corrosive fan

plastic mounting base for easy mounting on the roof

plastic canopy protecting the engine compartment

Acid-resistant fans suitable by their design for long ducts in various technological and air handling applications, in the chemical industry, petrochemistry and laboratories.

B2B clients will see their prices after logging in

58 539,00 CZK excl. VAT

70 832,19 CZK incl. VAT

Availability: on request [23.2.2026, 04:10] Update

Add to project

Insert into the design HVAC program

Insert into EasyVent

Product code: SP262600140

EAN: 8413893329448

Manufacturer: S&P SISTEMAS DE VENTILACIÓN, S.L.U. Read moreRead less

S&P SISTEMAS DE VENTILACIÓN, S.L.U.
Llevant, 4
Polígono Industrial Llevant
08150 Parets del Vallès
Barcelona – Spain
consultas[zav]solerpalau[teč]com
www.solerpalau.com/en-en/home

Product description

Cabinet

The fan is made of UV-resistant polypropylene. The fan includes a canopy and mounting base. A protective grille is placed on the discharge.

Running wheel

is radial with forward curved blades and made of polypropylene.

Motor

asynchronous with short armature, grease-filled ball bearings for life. Motor out of air stream. Operating temperature -10 to +60 °C. Insulation class F, protection class IP55.

Clamps

is located on the motor.

Mounting

is carried out on the mounting base included with the fan. The fan is started when connected to the pipe network for which it is intended, with the intake or discharge closed if necessary, so as to avoid overloading the fan. After start-up, the correct direction of rotation of the impeller must be checked and the current must be measured and must not exceed the rated current of the fan. If the current values are higher, the ductwork alignment must be checked. An overcurrent relay or other suitable motor protection must be included in the fan supply. If the motor overloads, the thermal protection will open the contactor control circuit and disconnect the fan motor. If this motor thermal protection is operating, it usually indicates an abnormal operating mode. In this case, it is necessary to check the piping network alignment and check the electrical parameters of the motor and wiring. If the fans are operated without this protection, the claim for a damaged motor is void. The enclosure must not transmit mechanical stresses from the pipework. A flexible connection to the ductwork must be used.

Instructions

Fans are suitable by their design for long ductwork in various process and air handling applications, in the chemical industry, petrochemical industry and laboratories. They are not suitable for the extraction of wood dust and grit, or other flammable or explosive mixtures.

Warning

The exact chemical composition of the substances to be conveyed must be determined when designing, and in case of uncertainty, the manufacturer should be consulted for suitability of the fan. The same rules apply for fan design as for all radial fans with forward curved blades.

Full description

Parametry

Základní údaje
Fan type	radial
Hazardous area classification	II 2 G (on request)
Explosivity group	IIB+H2, IIC engine (on request)
Temperature class	T4 (on request)
Explosion protection type	d (on request)
Fan material	Polypropylene
Installation	Mounting base
Weight [kg]	13,00 kg
Připojení
Diameter of inlet connection pipe [mm]	250 mm
Diameter of the connection pipe at the discharge [mm]	250 mm
Elektrické parametry
Power supply [V]	230/400 V
Ingress Protection	IP55
Engine type	AC
Maximum power input [W]	180 W
Maximum current [A]	1,11 A - 0,64 A
Vybavení
Ball bearings	Yes
Ball bearings	No
Check valve	No
Check valve	No
Delayed run-down	No
Delayed run-down	No
Adjustable coasting	No
Adjustable coasting	No
Hygrostat	No
Hygrostat	No
Motion sensor	No
Motion sensor	No
Adjustability	Yes
Adjustability	No
Particle filter	No
Particle filter	No
More intake ports	No
More intake ports	No
Sound insulation	No
Sound insulation	No
Další
Max. air temperature [°C]	60 °C
Maximum speed [min⁻¹]	950 min⁻¹

Safety regulations

Adherence to these instructions should not pose any safety, health or environmental risks in accordance with EC directives (CE marked). The same applies to other products used in the device or during installation. Consider the following warnings:

• Observe the safety instructions to prevent damage to the device or personal injury.
• The technical information in this manual must not be changed.
• It is forbidden to interfere with the motor of the device.
• In order for the device to comply with EC directives, the device must be connected to the mains in accordance with the applicable regulations.
• The device must be installed in such a way that under normal operating conditions it cannot come into contact with any moving part and / or live part.
• The device complies with the applicable regulations for the operation of electrical equipment.
• Always disconnect the device from the power supply before carrying out any work on it.
• Appropriate tools must be used when handling or maintaining the device.
• The device must only be used for the purposes for which it is intended.
• This appliance is not intended for use by children under 8 years of age and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible person. The user must ensure that children do not play with the device. Cleaning and maintenance of the appliance must not be carried out by children without supervision.

Downloads

Technical sheets, manuals and declarations

Datasheet .pdf (238.09 kB)

Declaration of conformity .pdf (359.50 kB)

CAD files

2D .dwg (249.33 kB)

2D .dxf (609.29 kB)

3D .dwg (729.76 kB)

3D .dxf (889.99 kB)