EP-15N electric heater

Electrically heated axial fans suitable for drying wet areas and for heating in industry and construction.

B2B clients will see their prices after logging in

32 610,00 CZK excl. VAT

39 458,10 CZK incl. VAT

Availability: on request [22.8.2025, 16:26] Update

Add to project

Goods cannot be ordered online.
Contact our sales specialists
or visit our branches.

Add to project

Insert into the design HVAC program

Insert into EasyVent

Product code: SP181100010

EAN: 8413893136848

Manufacturer: S&P SISTEMAS DE VENTILACIÓN, S.L.U. Read moreRead less

S&P SISTEMAS DE VENTILACIÓN, S.L.U.
Llevant, 4
Polígono Industrial Llevant
08150 Parets del Vallès
Barcelona – Spain
consultas[zav]solerpalau[teč]com
www.solerpalau.com/en-en/home

Product description

Cabinet

It is made of sheet steel, coated with a burning varnish. A stand made of steel pipe is screwed to the cabinet, which allows two basic positions for the fan to be placed and carried at the same time.

Running wheel

is axial, moulded from Al sheet. The blades are performance optimized.

Motor

is asynchronous with short armature and shielded pole. It is designed for continuous operation. The motor has grease-filled plain bearings for life. The motor has overload protection. Protection rating IP24.

Regulation

is carried out by 2 controls directly on the device. One sets the type of operation (see below), the other controls the switching thermostat. Using the switch on the rear panel, it is possible to select whether the thermostat will run the fan and heat or only heat when the fan is permanently on.

Electrical connection

The connection is by a cable that is routed out of the cabinet through a grommet and terminated with a 5-prong 400V fork.

The EP-3N model is single phase and the supply has a single phase fork.

Operation

The electrically heated fan is designed to operate on a horizontal pad or floor. When doing so, care must be taken to ensure that the inlet or discharge side is not covered by the heating rod housing. In this case, the air flow through the cabinet could be restricted and the temperature could rise, with a consequent risk of fire. If the air temperature rises, the unit will be switched off by the safety thermostat, whose reset button is located on the top of the cabinet.

Operating modes:
- fan only
- fan and half heating power
- fan and full heating power

Noise

emitted by the fan measured at a distance of 1.5 m in the free sound field with the fan placed on the floor is given in the table.

Variants

- EP-3N basic design 3 kW/230 V
- EP-5N basic design 5 kW/400 V
- EP-9N basic design 9 kW/400 V
- EP-12N basic design 12 kW/400 V
- EP-15N basic design 15 kW/400 V

Instructions

Electrically heated fans are suitable for drying wet areas and for heating in industry and construction. The places of use are mainly production halls, warehouse halls, common rooms, churches, exhibition halls, buildings and construction site facilities, garages and workshops.

Highlights

A safe distance from combustible structures, as specified in the user's operating rules, must be maintained.

Full description

Safety regulations

Adherence to these instructions should not pose any safety, health or environmental risks in accordance with EC directives (CE marked). The same applies to other products used in the device or during installation. Consider the following warnings:

• Observe the safety instructions to prevent damage to the device or personal injury.
• The technical information in this manual must not be changed.
• It is forbidden to interfere with the motor of the device.
• In order for the device to comply with EC directives, the device must be connected to the mains in accordance with the applicable regulations.
• The device must be installed in such a way that under normal operating conditions it cannot come into contact with any moving part and / or live part.
• The device complies with the applicable regulations for the operation of electrical equipment.
• Always disconnect the device from the power supply before carrying out any work on it.
• Appropriate tools must be used when handling or maintaining the device.
• The device must only be used for the purposes for which it is intended.
• This appliance is not intended for use by children under 8 years of age and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a responsible person. The user must ensure that children do not play with the device. Cleaning and maintenance of the appliance must not be carried out by children without supervision.

Downloads

Technical sheets, manuals and declarations

Datasheet .pdf (119.09 kB)

Operating Instructions .pdf (253.17 kB)

Declaration of conformity .pdf (349.75 kB)

CAD files

2D .dwg (893.81 kB)